Intelligent Water Monitoring
See every tank, sump, borewell and meter on one screen. Real-time level, flow and pump data stops overflows and dry runs, finds leaks while they are still small and shows exactly where your water goes.
Every litre measured, every loss visible
Find leaks, overflows and running taps within hours instead of at the end of the month’s bill.
Run pumps only when tanks need water, and stop them the moment tanks are full.
Dry-run and low-level cut-offs stop pumps from running without water and burning out.
No more climbing to rooftops or reading meters by hand: levels and readings arrive on their own.
You can’t manage water you can’t see
Most sites still run their water by guesswork. Someone checks the tanks, a pump is switched on by hand, and the first sign of a problem is an overflowing roof tank, a burnt-out pump or an unusually high bill.
Water also moves through many places at once: municipal inlets, borewells, sumps, overhead tanks, process lines and cooling towers. Without measurement at each point, it is impossible to tell normal use from waste.
Intelligent water monitoring puts a sensor at each of those points and brings the readings together, so levels, flows and pump status are visible in real time from anywhere.
Every part of your water system
Pick the measurements you need today and add more later on the same platform.
Non-contact radar or ultrasonic sensors read overhead tanks, sumps, wells and reservoirs continuously.
Electromagnetic, ultrasonic and pulse-output meters measure flow and totalised use per inlet, block or process.
Run hours, starts, schedules and dry-run trips for borewell, transfer and booster pumps.
Pressure transmitters show low pressure at the far end of the network and bursts or blockages.
pH, TDS, turbidity and residual chlorine for drinking water, process water and treated effluent.
Night-flow analysis and high-level alarms catch hidden leaks and overflowing tanks early.
Find hidden leaks from night-time flow
When a site is closed, water use should fall close to zero. If the main meter still shows steady flow at 2 a.m., something is running that shouldn’t be: a leaking pipe, a stuck float valve or a tap left open.
The system learns each site’s normal hourly profile and tracks its minimum night flow. When night flow rises above the baseline, or a tank keeps filling without any matching use, you get an alert that points to where to look.
Built for buildings, campuses and plants
Levels, flows, pumps and alarms for all tanks and buildings in a single web and mobile view.
Start and stop pumps on tank level or schedule, with dry-run and low-sump lockouts.
High and low level, overflow, leak, dry-run and no-flow alarms by SMS, email and app.
Daily, monthly and per-zone reports for billing, audits and water-saving targets.
Connect pulse and Modbus RS485 meters you already have, and add new sensors where needed.
LoRa and 4G links reach rooftop tanks, remote borewells and pump houses without new cabling.
Illustrative dashboard view
Levels, consumption and pumps at a glance
The dashboard shows the live level of every tank, the status of every pump and how much water each building or process used today, this week and this month.
Unusual days stand out immediately. A jump in consumption, a sump that won’t refill or a pump that keeps tripping is flagged with the reading behind it, so the team knows what to check before they leave the control room.
From sensor to action in four steps
Level sensors, meters and pressure transmitters are fitted on tanks and pipelines.
Readings travel over Modbus, LoRa or 4G to SCADA or the cloud.
Levels, flows and usage profiles are compared with set points and normal patterns.
Alerts go out, pumps start or stop, and reports are ready for review.
Sensors connect to your SCADA, PLC or BMS over Modbus RS485, across the site over a LoRa link, or to the cloud through a 4G gateway, so you can start with a few tanks and grow to the whole campus.
The hardware behind water monitoring
Non-contact radar and ultrasonic level sensors for tanks, sumps and wells. Contact us for options.
Ask for detailsPulse and Modbus RS485 meters for inlets, blocks and process lines, or connect your existing meters.
Ask for details
Carries Modbus data from rooftop tanks, borewells and pump houses over a LoRa link, without new cabling.
View product
4G gateway that sends levels and meter readings to the cloud for dashboards, reports and alerts.
View productOne partner from survey to a working system
We survey your site, select sensors and meters that suit each tank and line, and connect them to the dashboard or to the systems you already use.
Want to understand the sensor options first? Read our guide to water level monitoring systems.
Talk to an expert
Learn more from our engineering guides
Start saving water with data, not guesswork
Tell us about your tanks, pumps and meters and we’ll help you plan a pilot that shows where your water goes.
Book a demo Talk to an expert